|
|
|||
 |
 |
 |
 |
|
Industrial Evaporative Cooler |
Mobile Evaporative Cooler |
Commercial Evaporative Cooler |
Evaporative Cooling Module (ECM) |
 |
 |
 |
 |
| Heater Cooler Upgrade Package | Stainless Steel Precooler |
Converta-Pak upgrade retrofit for older coolers |
Rigid Cooling Media |
 |
 |
| Make up air unit with indirect fired natural gas/propane heater | Stainless Steel Gas Turbine Inlet Air Cooling/Filtration unit |
|
Additional products & technical data listed below |
|
Premier Industries, Inc., manufactures Evaporative Cooling Equipment featuring lifetime Stainless Steel housings and high efficiency rigid type Cooling Media with up to 98% cooling efficiency. Engineering and design assistance is available on the following web pages or from the factory direct. We can design and build equipment to meet virtually any evaporative cooling, filtration or air handling need!
|
EASY PAY: |
Table of Contents - Information:
About
evaporative cooling
- a primer on the technology
Gas Turbine Inlet
Air Evaporative Cooling
Industrial Evaporative
Coolers - Overview
Commercial
Evaporative Coolers - Overview
Make-Up
air units, Evaporative cooling and heating
Evaporative Cooling Modules
(Wet Sections / Air Washers) - Overview
Converta-Pak
- Overview
PreCoolers
Heater Cooling upgrade package
Portable
Evaporative Coolers - the Premier MobileCool© - Overview
Premier Cooling Media
Rigid
Cooling Media
Accessories
Technical
Data Index
Applications
and Design
Weather
data, available hours for cooling
Update on Indirect/Direct Evaporative
cooling process
After producing
and testing different versions of "Indirect/direct" evaporative cooler
prototypes, it is the opinion of Premier Industries, Inc., that this technology
is
not economically feasible.
A very small improvement in cooling efficiency is not an equitable trade-off for
the considerable additional cost.
Need a recommendation for
your cooling needs?
Follow this link and fill out
Premier Industries' design worksheet
Gas Turbine Inlet Filtration with Evaporative Coolers Filter housings with Evaporative Cooling to filter and cool the intake air to the turbine. Increase efficiency with colder, heavier air while filtering the air flow.
Industrial Evaporative Cooler Specification Page Stainless Steel housing with blower, motor, wet section and selected accessories. Highest cooling efficiency and quality available. Built to last almost forever!
Make-up Air Units: Evaporative cooling and heating Stainless Steel Evaporative Cooler with indirect gas fired heater.
Commercial Evaporative
Cooler Specification
Page Highest quality and cooling efficiency available in any
evaporative cooler for commercial use!
Heater
Cooler Upgrade Package
Evaporative
cooling module with selected accessories to retro-fit heaters with cooling
capability.
Evaporative Cooling Modules Specification Page Stainless Steel wet section complete with rigid media, water distribution system and selected accessories. Add evaporative cooling to heaters and ventilating units!
Converta-Pak© A Stainless Steel conversion unit to convert and upgrade older coolers to the newest evaporative cooling technology. Increase "swamp" coolers performance by 80%!
Pre-Cooler Stainless Steel wet section to precool air for heat exchangers (i.e. condensing
units). Increase air conditioner efficiency by as much as 30 to 50% during hot
periods and greatly extend compressor useful life!
NEW: OPTIONAL DRIFT
ELIMINATOR SECTION FOR PRE-COOLERS! Premier
Industries can now provide an integral 2.5" drift eliminator section on our
stainless steel pre-coolers. If you want to pre cool the inlet air for your
condenser coils but are concerned with water carry over, this economical
solution is for you! For additional information and specifications, click
HERE
Portable Evaporative Cooler (MobileCool©) A Stainless Steel portable (mobile) evaporative cooler for highly effective spot cooling. Evaporative cooling where you need it! Highest efficiency and toughest portable cooler available !!!!
Rigid Cooling Media High Efficiency cooling media up to 24" thick from stock, cut to size and shipped direct.
Stainless Steel Face Louvers : Custom fabricated to any size using Grade 304 S/S or Aluminum with birdscreen (optional).
Stainless Steel Dry Filter Racks: Custom fabricated to any size using Grade 304 S/S or Aluminum.
Stainless Steel Sumps for wet sections: Custom fabricated to any size using Grade 304 S/S. Optional mechanical float valve assembly and plumbing (drain, overflow and make-up water fittings) welded into the sump.
Stainless Steel Housings: Custom fabricated to size and configuration using Grade 304 S/S.
Accessories and Technical Data:
View and Print Premier Industries Company Brochure in PDF format
Welcome to
Premier's Home Page!
Click on an
image to go to the product overview